CCNA LAB - 2.1 InterVLAN Routing
On
CCNA Lab
Download
LAB 2-1: InterVLAN Routing
You are the Network Administrator at Ranet, and have to config both switch "Ranet-SW" and router
"Ranet-GW" via its console terminal as below:
1. Set Ranet-SW to seperate VLAN to be VLAN 10 and VLAN 20 and set its member as:
VLAN 10: Fa0/1, Fa0/2
VLAN 20: Fa0/3, Fa0/4
2. Enable feature "Portfast" on all access ports.
3. Set both Ranet-SW and Ranet-GW to route between VLAN 10 and VLAN 20:
- Use interface Fa0/0.1 and Fa0/0.2 on Ranet-GW as sub-interface for VLAN 10 and
VLAN 20 respectively.
- Please note that all hosts in each VLAN set IP Default Gateway to be the last IP of its
own subnet.
If everything is correct, All hosts will be able to connect with each other.
-------------- End -------------------
Solution
Ranet SW config
Ranet-SW>en
Ranet-SW#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Ranet-SW(config)#vlan 10
Ranet-SW(config-vlan)#vlan 20
Ranet-SW(config-vlan)#int ran fa0/1 -2
Ranet-SW(config-if-range)#switchport mode access
Ranet-SW(config-if-range)#switchport access vlan 10
Ranet-SW(config-if-range)#spanning-tree portfast
%Warning: portfast should only be enabled on ports connected to a single
host. Connecting hubs, concentrators, switches, bridges, etc... to this
interface when portfast is enabled, can cause temporary bridging loops.
Use with CAUTION
%Portfast will be configured in 2 interfaces due to the range command
but will only have effect when the interfaces are in a non-trunking mode.
Ranet-SW(config-if-range)#int ran fa0/3 -4
Ranet-SW(config-if-range)#switchport mode access
Ranet-SW(config-if-range)#switchport access vlan 20
Ranet-SW(config-if-range)#spanning-tree portfast
%Warning: portfast should only be enabled on ports connected to a single
host. Connecting hubs, concentrators, switches, bridges, etc... to this
interface when portfast is enabled, can cause temporary bridging loops.
Use with CAUTION
%Portfast will be configured in 2 interfaces due to the range command
but will only have effect when the interfaces are in a non-trunking mode.
Ranet-SW(config-if-range)#int gig1/1 2
Ranet-SW(config-if)#switchport mode trunk
Ranet-SW(config-if)#
%SYS-5-CONFIG_I: Configured from console by console
Ranet-SW#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Ranet-SW#
Ranet GW config
Ranet-GW>en
Ranet-GW#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Ranet-GW(config)#int fa0/0
Ranet-GW(config-if)#no sh
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Ranet-GW(config-if)#int fa0/0.1
Ranet-GW(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/0.1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.1, changed state to up
Ranet-GW(config-subif)#encapsulation dot1Q 10
Ranet-GW(config-subif)#ip add 192.168.0.142 255.255.255.240
Ranet-GW(config-subif)#int fa0/0.2
%LINK-5-CHANGED: Interface FastEthernet0/0.2, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.2, changed state to up
Ranet-GW(config-subif)#encapsulation dot1Q 20
Ranet-GW(config-subif)#ip add 192.168.0.158 255.255.255.240
Ranet-GW(config-subif)#
%SYS-5-CONFIG_I: Configured from console by consoleRanet-GW#
Ranet-GW#sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
192.168.0.0/28 is subnetted, 2 subnets
C 192.168.0.128 is directly connected, FastEthernet0/0.1
C 192.168.0.144 is directly connected, FastEthernet0/0.2
Ranet-GW#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Ranet-GW#
------------------- End --------------------
Now, all host will be able to connect with each other.
You can download this solution here.
Copyright by http://www.lecuong.info
